SAILAsterix
A FREEDOM 40 · A NEW CHAPTER

Mizzen mast restoration

Asterix · Masts and sails · Refit in Oxnard

A fresh finish
for the mizzen.

Removing old fittings, filling the holes and applying two coats of lamp-black epoxy—all from the bosun’s chair. The painting is complete; cables and masthead fittings are still to come.

Refit in progressUpdated 8 November 2026
22 April 2026 · 13:58Fantasy at her berth, with the view focused on the mizzen mast and aft deck.

Current position · 8 November 2026

Completed: redundant fittings removed, old holes filled, surface sanded and washed, halyard-entry fitting re-riveted, masthead truck spray-painted and two coats of lamp-black epoxy applied to the mast.

Milestone reached: the second coat was completed on Tuesday 3 November.

Still ahead: the VHF/AIS aerial cable and remaining masthead equipment. The painting is complete; the wider mast work remains open.

A tired finish and a collection of old fittings.

The mizzen’s old coating was patchy, and there were fittings and fixing holes to work through before we could give the mast a fresh finish.

Our job was to remove what was no longer needed, repair the old holes and prepare the surface. As with so much of the refit, the visible result would come at the end of a lot of small jobs.

Up the mast, one fixing at a time.

During the October work I drilled out old rivets and removed redundant fittings. There was a mixture of stainless steel and aluminium to deal with, and several drill bits were lost along the way. The old masthead light and aerial fittings came off for cleaning and assessment.

We filled the unwanted holes with epoxy and lamp black, then sanded the repaired areas. By the end of October the mizzen was prepared for painting, although another trip aloft on Monday 2 November found the final holes I had missed. Those were filled and sanded too.

Next came washing the mast and letting it dry. I also re-riveted the mizzen halyard-entry fitting. The riveter refused to grip properly, which meant another trip to Harbor Freight for a replacement before that small job could be finished.

None of these jobs was particularly large by itself. Together they were the preparation needed before opening the paint.

Small batches.
A long way above the deck.

Painting from a bosun’s chair makes even mixing the next batch awkward. I prepared measured quantities of epoxy in syringes below, so I could mix small amounts as I worked my way down the mast.

At the top I cleaned and spray-painted the crown, or truck, of the mizzen. Then I came down applying the first coat of lamp-black epoxy to the mast. Getting that first coat on felt like a major milestone.

3 November 2026Preparing small batches below before taking them up the mast.
3 November 2026Two coats of lamp-black epoxy on the mizzen: the coating milestone reached.

On Tuesday I went back up for the second coat and fitted a couple of small stainless rivets in the collar. It was windy. One gust caught a paint tray and caused a little spillage, so I worked with smaller batches to keep the tray less full.

By the end of Tuesday the mizzen had its two coats. After all the filling, sanding, washing and repeated journeys aloft, seeing the fresh black finish was extremely satisfying.

What this stage included.

Work Position at 8 November
Redundant fittings and rivets Removed during preparation
Unwanted fixing holes Filled with epoxy and lamp black; sanded
Mast surface Sanded, washed and dried before coating
Halyard-entry fitting Re-riveted
Masthead truck Cleaned and spray-painted
Mast coating Two coats of lamp-black epoxy, completed 3 November

This is the record of our work aboard Asterix. It does not describe a completed replacement of every masthead fitting.

The finish is on.
The masthead still needs work.

We still need to run a VHF/AIS aerial cable up the mizzen and fit its Windex. There are messengers in the masts, but we have not yet established how useful they will be for pulling the new cables.

The main mast has its own cable and masthead jobs, covered in the track project. The mizzen deck-collar sealing is recorded separately in the deck leaks and headlining project.

For now, the painting is done. After six to eight trips up the mast during the week, I am looking forward to a week working inside the boat.